INJECTOR TOOLS
Pneumatic Injector Puller Set, 51107
Pneumatic Injector Puller Set, 51107
Air powered tool that uses vibrations and 20-30Nm of torque to remove especially tight or seized injectors.
The tool is accompanied by a comprehensive set of adapters, including solenoid screw and fuel feed line adapters, offering versatility and compatibility with a range of injector types.
Use the 5-8Bar air source tool to link the fuel injector and impact and disassemble the particularly tight fuel injector M8, M10, M12, M14, M15, M17 и M19.
Suitable for Bosch, CAT, Cummins, Denso, Delphi, Siemens Common Rail injectors which have solenoid coil or screw connections.
.Made in China
27mm 1/2" Dr. Vacuum switch socket, 44327
1/2" Dr. Vacuum switch socket, 44327
Size: 27 mm
Material: Cr-Mo
Produced by Force, Taiwan
1/2" Dr. Vacuum switch socket, 44322
1/2" Dr. Vacuum switch socket, 44322
Size: 22 mm
Material: Cr-Mo
Made in Taiwan, Force
9 pcs. Common rail Diesel injector puller extractor set, 50350
9 pcs. Common rail Diesel injector puller extractor set
Description: Slide hammer for DB CDI-engines & Mercedes CDI engines OM 611, 612, 613, Mazda BT50, Hyundai, Sanyong, Jeep, ML 270 etc.
For removing stuck and the seized common-rail injectors without removing the cylinder head.
The sturdy construction will enable the swift removal of even the most severely seized in injector.
Most often injectors can be removed without damage, allowing the injector to be reused.
17 pcs Diesel injector seat cutter set, 50682
17 pcs Diesel injector seat cutter set, 50682
This set is used to clean and decarbonise injector seats when changing injectors.
It helps to avoid blow-back due to poorly seated injectors.
Suitable for a wide range of vehicles of modern Common Rail Vehicles with injectors from Delphi and Bosh.
Contents:
14mm x 14mm Flat Reamer (for AUDI)
15mm x 19mm Flat Reamer
15.5mm x 15.5mm Flat Reamer
15.5mm x 15.5mm Angled Reamer
17mm x 17mm Angled Reamer
17mm x 17mm Flat Reamer
17mm x 17.5mm Flat Reamer
17mm x 19mm Flat Reamer
17mm x 19.5mm Flat Reamer
17mm x 20mm Flat Reamer
17mm x 21mm Angled Reamer
17.5mm x 20.5mm Angled Reamer
19mm x 21.5mm Flat Reamer
T-handle; Pilot Hex 19 x 170mm; 15.5 X 250mm Cutter; 2.5mm Hex Key
Made in China
BMW Common rail injector set, 50630
BMW Common rail injector set, 50630
Special tool pulling out stuck injectors
with BMW Diesel Engine Code with M47TU / M 47T2 / M57 / M57TU / M 57T2
The support on the cylinder head enables high pull-off
disassembly of the cylinder head is therefore not necessary
The particular form of puller allows safe and precise extraction, especially in very tight injectors / injectors.
Contents
- 2 support feet 115 mm
- 2 support feet 140 mm
- Supporting bridge with ball bearing
- Spindle M16 with unilateral M17 thread for mounting in the injector
- 29mm socket wrench for removing the electrical unit
- Allen key for removing the injector needle
For the following BMW - types
In contrast to solutions with impact hammer, the injectors are removed with this tool by even train and in the optimum position for installation position.
E38: 730 d
E87: 118 d / 120 d
E46: 318 d / 320 d / 330 d
E39: 520 d / 525 d / 530 d
E60/E61: 520 d / 525 d / 525 xd / 530 d / 530 xd / 535 d
E63/E64: 635 d ( 04-10 )
E38/E65/E66: 730 d
E83: X3 2.0 d / 3.0 d
E53/E70: X5 3.0 d
E90/E91: 316 d / 320 d
E90/E91/E92/E93: 325 d ( 06-10 ), 330 d / xd ( 98-08 ), 335 d
This also applies to same engine in a Land Rover - types such as
Range Rover: 2.5 DT Year 1994 - 2002
Range Rover: 3.0 TD6 2002 - 2006
Freelander: 2.0 TD4 2002 - 2006...
1/2"Dr Injection Line socket, 50802
1/2"Dr Injection Line socket
Set of special open twelve-walled keys for unwinding and turning the nuts of the high pressure tubes to the fuel nozzles or the pump.
Suitable for BMW Diesel engines and OPEL 2.5 TD engines.
Material: Cr-V
Size: 14; 17; 19 mm ...
14 Pcs Injection Puller Tool Bosch, Delphi, Denso and Siemens Diesel Injector Remover, 50348
14 Pcs Injection Puller Tool Bosch, Delphi, Denso and Siemens Diesel Injector Remover, 50348
Application:
Suitable for the fast and reliable removal of Bosch, Delphi, Denso and Siemens diesel Injectors.
Includes:
Comprehensive set of 1/2in.Dr Injector Sockets - 25, 27, 29, 30 mm
7 Injector Adaptors and Slide Hammer
Blow mold case for storage
Contains:
Impact Hammer: 3.6 kg
Overall length (. M handle) slide hammer: 510 mm
- Length of the handle: 110 mm
- Ball joint adapter
- Adapter: M14 x 1.5 for Delphi
- Adapter: M17 x 1 for Bosch
- Adapter: M20 x 1 for Denso
- Adapter: M25 x 1 for Siemens
- Adapter: M27 x 1 for Siemens
- Adapter: M27 x 1 for Bosch
- 4 slotted 6-point socket wrench inserts ( 100 mm long) for electrical unit: 25 - 27 to 29 - 30mm
- 10 mm hex bit application, 1/2 "drive
Made in China
6 pcs Slide hammer injector puller set for Mercedes Benz CDI engines
6 pcs Slide hammer injector puller set for Mercedes Benz CDI engines
Designed for fast and professional remove of Mercedes-Benz car injectors without the need to remove the cylinder block.
Components made of CR-Mo and S45C steel.
Suitable Mercedes with CDI engines.
Application: For Mercedes-Benz CDI engines 611.612.613, etc.
Extra long Oxygen sensor socket 22 mm, 50491
Extra long Oxygen sensor socket 22 mm, 50491
Material: CR-MO
Suitable for: BMW, Ford, Mercedes Benz C and E class (602, 605, 606 engines), Opel, Rover, VAG, Volvo, VW, Audi, Skoda, Seat.
1/2 ", Size: 22 mm, L = 150 mm
3 Pcs Glow plug pullerand reamer set, 50336
3 Pcs Glow plug pullerand reamer set, 50336
Suitable for removal of stubborn glow plugs on Mercedes Benz vehicles with melted electrodes