Magma

Draper Bearing, Seal and Bush Insertion/Extraction Kit (27 piece), 50092

Expert Quality, bearing, seal and bush insertion and extraction kit, perfectly designed to aid with accurate and controlled insertion or removal of a host of different bearings, including normal bearings, silent bearings, hydraulic bearings, rubber bearings, bearing bushes, shaft seals etc.
Each kit comprises of 22 adaptor rings and five fine thread puller bars with hex. nut ends, contents of each kit is the following:

1 x 34mm x 44mm adaptor ring, 1 x 36mm x 46mm adaptor ring, 1 x 38mm x 48mm adaptor ring, 1 x 40mm x 50mm adaptor ring, 1 x 42mm x 52mm adaptor ring, 1 x 44mm x 54mm adaptor ring, 1 x 46mm x 56mm adaptor ring, 1 x 48mm x 58mm adaptor ring, 1 x 50mm x 60mm adaptor ring, 1 x 52mm x 62mm adaptor ring, 1 x 54mm x 64mm adaptor ring, 1 x 56mm x 66mm adaptor ring, 1 x 58mm x 68mm adaptor ring, 1 x 60mm x 70mm adaptor ring, 1 x 62mm x 72mm adaptor ring, 1 x 64mm x 74mm adaptor ring, 1 x 66mm x 76mm adaptor ring, 1 x 68mm x 78mm adaptor ring, 1 x 70mm x 80mm adaptor ring, 1 x 72mm x 82mm adaptor ring, 1 x 75mm x 85mm adaptor ring, 1 x 80mm x 90mm adaptor ring, 1 x M10 pulling spindle, 1 x M12 pulling spindle, 1 x M14 pulling spindle, 1 x M16 pulling spindle, 1 x M18 pulling spindle.

The set is in case.

Made in China

• Application: Designed for crimping cables and wires with sizes from 6 mm² to 70 mm² (square millimeters).
• Pressure/Force: The tool typically applies a force of 5 to 8 tons (70 kN).
• Made in China

Pneumatic Injector Puller Set, 51107

Air powered tool that uses vibrations and 20-30Nm of torque to remove especially tight or seized injectors.
The tool is accompanied by a comprehensive set of adapters, including solenoid screw and fuel feed line adapters, offering versatility and compatibility with a range of injector types.
Use the 5-8Bar air source tool to link the fuel injector and impact and disassemble the particularly tight fuel injector M8, M10, M12, M14, M15, M17 и M19.
Suitable for Bosch, CAT, Cummins, Denso, Delphi, Siemens Common Rail injectors which have solenoid coil or screw connections.

.Made in China

Universal ball joint puller, automobile, 23 mm, 50049

Specification:
External clamping width: 23 mm
Clamping depth: 65 mm
Width: 100 mm
Spindle length: 35 mm
Thread dimension: M14 x 1.5
Width across flats: 19 mm

Applicable:
For easy ejection of ball joint bolts, particularly for many cars from the following manufacturers: Audi, BMW, Fiat, Ford, Daimler-Chrysler, Opel/Vauxhall, Nissan, Toyota, VW, Volvo.

Made in China

1/2"Dr. 22mm Oxygen Sensor Socket, 51082

Material: Cr-V
Drive: 1/2”, 6-pt.
Overal lenght: 85mm
Slot size: 8mm
Size: 22mm

Made in China

Spring compressor for Mercedes, 50073

Drop forged yokes head threated
Telescopic construction with 3-point safety interlock and automatic freeheelat and of stroke.
Maximum compression range 325 mm.
Minimum compression range 120 mm.

Applicable for:

Mercedes: W123, W124, W129, W201, W202, W210

Mercedes: W114, W115, W116, W123, W124, W126, W129, W140, W201, W202, W203, W210.

Other models: GM, Peugeot, Rover, Hyundai, Saab, Volvo, Volkswagen, Fiat, Mazda, Toyota, Nissan, Mitsubishi.

The set is in blue case.

Made in China

18 Pcs 1/2" Drive Wheel Nut Socket Set, 51168

A Professional-grade solution designed for the safe and efficient removal of standard, damaged, and locking wheel nuts. Each socket is equipped with a protective plastic sleeve to prevent scratches and damage to alloy wheels during operation.

This comprehensive set includes double-ended twist sockets, specifically engineered for removing damaged nuts and bolts, as well as locking wheel nuts. The double-ended wheel nut sockets are ideal for situations where the chrome cap is missing or damaged, ensuring a secure grip and easy removal.

Manufactured from high-quality chrome molybdenum (Cr-Mo) steel, the sockets offer exceptional strength, impact resistance, and long service life. Designed for use with 1/2" drive impact tools, this set is suitable for professional workshops, tire service centers, and demanding home users.

1/2"Dr. 19mm Oxygen Sensor Socket, 51081

Material: Cr-V
Drive: 1/2”, 6-pt.
Overal lenght: 85mm
Slot size: 8mm
Size: 19mm

Made in China

11 pcs Bearing and seal driver set, 50130
For the installation of bearings and seals. Helps avoid damage to bearing and seal faces.
This set will provide the correct size driver for 99%, bearings, bush and oil seal installations.
The reverse side of the collar can also be used to drive seals.
Supplied with a strong blow mould case.
Ideal for car, commercial motorbike or any application that has bearings or seals.
Always drive that bearing in square and flush first time.

1/2"Dr. 17mm Oxygen Sensor Socket, 51080

Material: Cr-V
Drive: 1/2”, 6-pt.
Overal lenght: 85mm
Slot size: 8mm
Size: 17mm

Made in China

Fuel injection test set, 50199

The car fuel pressure diagnostic kit is suitable for most vehicles with a fuel injection system with petrol or gas engines (except Bosch, CIS Jetronic, Throttle Body Systems on GM cars).
Not suitable for diesel engines with high pressure injection pump or direct injection engines due to the low pressure range of the manometer.
Fuel pressure testing is an essential part of the fuel injection system troubleshooting process.
Contents:
The set is equipped with various fittings and connection hoses for testing.
15 "length hose is used for direct connection to 1/4" SAE standard fuel pump shredder valve
An 8 "length hose is for the M6 ​​fuel pressure test hole, and there are also adapters M8; M10; M12; M14 for the corresponding test port on fuel rail.
Aluminum tee to support the connection between the fuel pump and the engine for most cars.
Manometer, protected with a rubber shell, with a diameter of the dial 3-1 / 2 ", with a range of 0-10bar (0-140psi) and two-color coded scale for easy reading. The hoses use rubber nylon resin and the built-in nylon can strengthen the hose with increased stress resistance. The pressure relief valve and 16 "fuel drain hose help to safely release the pressure and easily restore the fuel.
Fuel pump pressure check:
The manometer is designed to easily and quickly check the pressure of the fuel injection pump and the fuel flow.
You can compare the pressure value with the manufacturer's recommended reference range to help diagnose the petrol engine system.
Low fuel pressure can be caused by kink/leak/clog on inlet supply side components, a bad fuel pump or regulator, low tank pressure
High fuel pressure may be caused by a bad fuel pressure regulator or kincked outlet return line.

Made in China

BMW Drive Shaft and Differential Flange Nut Tool Set, 51019

Features:
For removing and installing of the drive shaft nut allows inserting of the rear differential pinon seal suitable for BMW vehicles with rear and four wheel drive.
Suitable for BMW E70, E90, E91, E92 with N54 B30 engine.
Contents:
Open end spanner 50 mm - OEM # 33 5 040 – For BMW E70, E88, E90, E91, E92
Flange holding tool - OEM# 23 0 020 – For BMW E70, E82, E88, E90, E91, E92, etc.
Multi-point ring spanner 65 mm – OEM# 33 5 050 – For BMW E70, E82, E90, E91, E92, E93
Multi-point socket 34T – OEM# 3 35 060 – For BMW E70, E82, E90, E91, E92, E93
Seal ring drift – OEM# 3 35 080 - For BMW differential: HAG 215 Sp, HAG 220kom, HAG 225kom, HAG type G

OEM#: 33 5 040, 33 5 050, 33 5 060, 33 5 080, 23 0 020

Made in China

HGV Diesel Injection Nozzle Socket, 50825

Features:
Used to install and remove the diesel injection nozzle on MAN, Mercedes-Benz and Scania commercial vehicles.
Specially designed with window, toothed end and M14x1.5 pulling force screw.
Applicable: Mercedes-Benz CRD, MAN & Scania

Made in China

CV Joint Assembly Removal Tool, 50044

Description:
- For removing CV joints on front wheel drive cars without removing the drive shaft
- Quickly removes the CV joint from the drive shaft without damaging the joint, and keeps hands free for releasing retaining circlip
- A robust tool for front wheel drive cars
- Suitable for most vehicle
- Removes CV joints without removing drive shaft
- Time saver
- Essential service tool
- Phosphate Coated for long heavy duty service life

4 Pcs Truck Diesel Injector Socket Set, 50650

Contains:
1 pc  Hex 32mm x 70mm x 4 teeth (with M14 x 1.5 receiver thread) for Mercedes-Benz, Neoplan and Setra.
1 pc 1/2"Dr. x 72mm x 4 teeth for Mercedes-Benz.
1 pc Hex 32mm x 120mm x 4 tooth for MAN and Mercedes-Benz.
1 pc 1/2"Dr. x 120mm x 3 teeth for MAN and Mercedes-Benz.
Also suitable for some Iveco, Scania and Renault commercial vehicles.

Made in China