INSTRUMENTS

HGV Diesel Injection Nozzle Socket, 50825

Features:
Used to install and remove the diesel injection nozzle on MAN, Mercedes-Benz and Scania commercial vehicles.
Specially designed with window, toothed end and M14x1.5 pulling force screw.
Applicable: Mercedes-Benz CRD, MAN & Scania

Made in China

SCANIA - 80mm 8-pt. Front Hub Nut Socket, TP9T1422
Description:
This eight sided 80mm socket is designed for the removal of front hub nut found on Scania trucks.
Lenght: 104 mm
Innerdiameter: 80 mm
Outerdiameter: 100 mm
Driven by 41mm Hex
Weight: 1800 gr

Made in Taiwan

Mercedes Benz Ball Joint Remover Installer Set, 50453

Spesialized 10-Piece tool kit to service all of the pressed-in ball joints incorporated in the Mercedes W210 / W211 / W220 / W230 / W163/ W164 suspensions.
This tool set allows servicing (installation and removal) of the specified ball joints on the vehicle. This saves tremendous time and effort by avoiding the necessity of disassembling the brake system and other suspension components that would disturb suspension alignment.
Includes:
C-Clamp press tool forged (not cast) form SCM440 Steel (HRC 38-42 hardness)
Front Suspension Ball Joint press fixtures for W220 / W211 / W230 Chassis - used in Conjunction with the C-Clamp Press.
Front Sway Bar Ball Joint (pressed into control arm) press fixtures for W220 /
W211 - used in Conjunction with the C-Clamp Press.
Front & Rear Suspension Ball Joint press fixtures for W163 / W164 Chassis - used in Conjunction with the C-Clamp Press.
Ball joint socket (4-prong) for servicing front ball joint on W163 / W164 Chassis
Application: Mercedes Benz
W210 Chassis - 1995-2002 E Class
W211 Chassis - 2002-2009 E Class
W220 Chassis
W230 Chassis
W163 Chassis - 1998-2005 M Class
W164 Chassis - 2006-present M Class

Made in China

Piston Ring Compressor 60-175 mm, 50091

With Safety valve Special spring steel
Ratchet type complete with hex spanner
Capacity: 60-175mm
Height: 150mm (6")

Made in China

Coil Spring Compressor For Wishbone Suspensions, 50452

Suitable to work on lower supports with a small access (< 30 mm)
Suitable for more coil springs - Working range: 95 - 220  mm
100Nm Extension torque bar controls excessive torque being applied
Holder discs with wide application
Applicable to vehicles with a swing arm diameter of 30 mm and bigger.
Applicable:
Chrysler, Citroen, Ford, Honda, KIA, Mitsubishi, Peugeot, Renault, Seat, Skoda, Suzuki, Toyota, Volvo, Volkswagen,  etc.
BMW 3 series (1996-2013)
Mercedes Benz W202/ W204 (1997-2013)
Includes:
150 mm steel pressure plate
130 mm steel pressure plate
Compressing bar
Extension bar with 100 Nm torque control for use with impact wrench.

Made in China

18 pcs Universal caliper wind back set, 50060
• Provides both left-handed and right-handed thrust bolt assemblies
• Complete set of adaptors for a wide range of vehicle applications
• Designed for push back and wind back brake pistons
• Left-handed thrust bolt required for Ford, Citroen, and Renault applications
• Adaptor plates with thrust bolt assembly and reaction plate are precisely made
• Prevents damaging pistons and seals
• Updated adaptor set applicable for wide variety of vehicles"

5 Pcs Ball Joint Separator, 50435

Content:
Ball Joint Separator
Tie Rod And Ball Joint Remover
Conical Pitman Arm Puller
Pitman Arm And Tie Rod End Puller
Pitman Arm Puller

Description:
Ball Joint Separator - For separating the ball joint from the spindle support arm on domestic and import front wheel drive vehicles adjustable for different size ball joints
1-1/8" & 2-1/8" (30 & 56mm) maximum opening capacity
7/8" jaw spread, 2-1/4" throat depth
Tie Rod And Ball Joint Remover - A universal heavy-duty puller that removes a wide range of tie rods and ball joints from a variety of cars, trucks, SUVs and heavy-duty vehicles.
0 to 2-1/2" jaw spread, 3-1/4" throat depth
Conical Pitman Arm Puller - Designed to fit securely on Pitman arms for compact and mid-size cars.
3/4-16 x 4-3/4" forcing screw provides enough power to remove stubborn pitman arms.
Pitman Arm And Tie Rod End Puller - This versatile tool can be used as a pitman arm remover for many small, domestic rear-wheel drive vehicles, or as a tie rod end puller for many domestic and import vehicles. The jaws, with a spread of 1", give a secure positive grip in tight workspaces.
1-1/8" jaw spread, 2-1/8" throat depth
Pitman Arm Puller - This puller will handle nearly any pitman arm job on passenger cars and light trucks. It features special forged jaws, shaped to fit most models, keeping a solid grip while you work.
1-11/32" jaw spread, 2-1/2" throat depth

Made in China

Windshield Removal Tool Set, 50220

This universal kit includes all of the specialised tools required to safely and quickly remove windshields from a wide variety of vehicles.
Item is supplied with a rubber gasket knife, cutting wire, two (2) handles, wire feeder tool, trim pad remover and molding release tool.

Set includes:

- Wire: Three strong galvanised steel wires braided to form one wire
- 2 pcs Wire gripping handles: Feed the wire through the hole in the wedge shaft. Loop it through the hole at the top of the shaft. Then back into the handle. Pressing the wedge back into the handle, the wire is held.
- Windshield removal tool: Cuts the vinyl adhesive compound around the windshield.
- Wire feeder tool: Designed for easy and flexible insertion of wire through polyurethane, allowing speedy removal of bonded windshield
- Trim pad remover: Place the tool under the edge of the door upholstery panel and insert it into the fastener as far as possible, then simply pry up.
1PC stainless steel wire with reel.
2PCS Wire gripping handles.
1PC Windshield removal tool
1PC Wire feeder tool
1PC Trim pad remover
1PC Windshield molding release tool

Made in China

21 PCS Universal Brake Caliper Wind Back Kit Suitable for push back and wind back brake pistons. Includes left- and right-handed thrust bolt assemblies. Left-handed thrust bolt required for Ford, Citroen and Renault applications. Adaptor plates with thrust bolt assembly and reaction plate. Helps prevent damage to pistons and seals. Updated adaptor set suitable for a wide variety vehicles. Supplied in carry-case.

Injector Seat and Shaft Cleaning Tool Kit, 50883

It contains a set of tools that ensure effective cleaning of the injector hole and the surface of the bed before inserting the new nozzle. It is used in a wide range of vehicles.
Suitable for Fiat Citroen BMW Peugeot Renault and Mercedes-Benz
Includes:
4 pcs cleaning brushes, brush holder, 3 pcs injector seat mill, cutter guide, sealing ring puller, brush holder extension injector seat and shaft cleaning kit, Note: only use brushes clockwise.
3 pcs conical sleeves for the guide pin 17 / 18.4 / 19 mm.
Guide bolts for sealing seat mills with 19 mm external hexagon head.
3 pcs milling heads:
15 x 19 mm diameter - Mercedes CDI
17 x 17 mm diameter - BMW, Peugeot, Citroen, Renault for Delphi / Bosch injectors
17 x 17 mm diameter 30° bevelled -  Fiat and Iveco sealing ring extractor.
Joint shaft with 6.3 mm (1/4 inch) hex bit holder for drill holders, for brushes with 6.3 mm (1/4 inch) hex bit holder.
2pcs  brush heads with 19.5 mm diameter, 2 pcs long, thin brushes for nozzle needle shaft.
6 pcs guide plugs for closing the nozzle needle shaft with holder for removal and installation.

Made in China

M16x2.5 Spindle for Press and Pull Sleeve Kit, 50093-4

Pulling spindle with nuts and thrust bearings.

Size: M16x2.5 mm

Length: 450 mm

Material: carbon steel

Made in China

35 pcs Universal caliper wind back set, 50064

Applicable: Alfa Romeo / Audi / Austin / BMW / Citroen / Ford / General Motors / Honda / Jaguar / Mazda / mercedes / Mitsubishi / Nissan / Opel / Renault / Rover / Saab / Toyota / Subaru and Volkswagen

• 7mm  Audi, BMW, Ford, Peugeot, Opel, VW
• 8mm  Audi, BMW, Ford, Peugeot, Opel, VW
• 2 бр. ударни челюсти 
• 1-1: с дясна резба
• 1-2: с лява резба
• 2- Citroen: BX (83), BX 16V (88-), Honda
• 3- Audi: A3, A4, A6, A8, BMW, Citroen: XM, XM Turbo CT 20, Xantia, C5, Ford: Mercury, Monarch, Thunderbird, Honda, Jaguar, Mitsubishi, Nissan, Peugeot: 406, 806, Rover, Toyota, VW, Volvo
• 4- Alfa Romeo: 146, Fiat: Uno, Brachetta, Ford: Escort, Mondeo, Honda: Civis, Accord, Rover: 220, Saab: 99L, 9006- Jaguar: S-Type
• 7- Jaguar: S széria, Opel: Astra G, Corsa C, Zafira
• 8- GM Motor
• 9- GM Motor
• 0- GM Motor
• O- Citroen: ZX, XM, Xantia, BX, C3, C5
• 11- Jaguar: S-Type
• 12- BMW Mini
• A- Nissan: Primera, Bluebird, Opel: Astra C, G, Zafira
• B- Ford: Mercury, thunderbird, Lincoln: Continental, Subaru: 1600, 1800, Lim., Kombi, Tourismo 4WD, 1800 GT, GTSXT
• C- Nissan: Primera, Opel: Vectra, Toyota: Avensis
• D- Citroen: BX
• E- Nissan: Maximas
• F- Peugeot: 206
• J- Alfa Romeo: 155, 164, Audi: 80, 9, A3, A4, A6, Citroen: ZX, Fiat: Tipo, Uno, Ford: Sierra, Granada, Thunderdird, Honda CRX, Accord, Prelude, Legend, Jaguar: XJ, Lancia: Dedra, Delta, Thema, Kappa, Nissan: 280 ZX, 300 ZX, Bluebird, Silvia, 100 NX, Primera, 200 SX, Maxima, Peugeot: 306, 309, 405, Renault: Master, Rover: 216, 820, 825 Saab: 9000, Seat: Toledo, Ibiza, Subaru, VW: Passat, Golf, Vento, Transporter, Volvo: S40, V40
• K- Citroen: C5
• K1- Citroen: C5
• K2- Audi: A8, S8
• M- Nissan: Primera
• N- Alfa Romeo: 164, Audi: 200, Coupe GT, 80, 200, Quqttro, 90, Ford: Mondeo, Lancia, VW: Golf Scirocco
• P- Citroen: C3
• R- Ford: Telstar, Laser, Mazda: 323, RX7, 626, 929, Mitsubishi: Galant, Toyota: Celica, Corolla
• Z- BMW, Mini
• H6- BMW: 740, Mini, Opel: Astra G, Zafira
• H7- BMW: 740, Mini, Opel: Astra G, Zafira
• P3.0- Opel: Astra C, Zafira, Corsa C, Vectra
• P5.5- Opel: Astra C, Zafira, Corsa C, Vectra

Made in China

M14x2.0 Spindle for Press and Pull Sleeve Kit, 50093-3

Pulling spindle with nuts and thrust bearings.

Size: M14x2.0 mm

Length: 450 mm

Material: carbon steel

Made in China

M12x2.0 Spindle for Press and Pull Sleeve Kit, 50093-2

Pulling spindle with nuts and thrust bearings.

Size: M12x2.0 mm

Length: 450 mm

Material: carbon steel

Made in China

Vacuum tester and brake bleeder, 50411

The Vacuum/Pressure Pump may be used for many different tasks.
1. Testing vacuum-operated components (door locks, actuators,etc)
2. Engine mechanical testing (valves, cam timing, head gasket, etc)
3. Brake and clutch hydraulic system bleeding
4.Measurement of vacuum supplied by booster reservoirs solenoids or the engine.
Features:
Checks vacuum/pressure
Operated automotive components.
Can be used to bleed hydraulic  systems or siphon fluids.
Detailed used instructions and photos inside of case.
Hand pump with built-in vacuum pump
Assorted vacuum hoses
Assorted hose adapters
Universal cup adapter
4 ounce reservoir jar
Jar lids