INSTRUMENTS

Mini sliding hammer with 10 pcs glue pads, 160-3123

Complete with 10 pcs glue pads and a mini sliding hammer for reducing small dents on the vehicle body. It is recommended for manual operation.
Contents:
Mini sliing hammer 0.95LB (0.43 kgs }
10 pcs Glue Pads (Plastic Connectors)

Made in Taiwan

3 Jaws Gear puller 12”, 50742F

Heat treated, forged alloy steel with rust-resistant.
Precision-machined, hardened and tempered, self-centering steel screw with black finish.
Zinc plated jaws and hardware.
Removes gears, pulleys, flywheels, etc, from shaft.
Applies even pressure to prevent damage.

Puller Size: 12”

Made in China

4 Pcs Truck Diesel Injector Socket Set, 50650

Contains:
1 pc  Hex 32mm x 70mm x 4 teeth (with M14 x 1.5 receiver thread) for Mercedes-Benz, Neoplan and Setra.
1 pc 1/2"Dr. x 72mm x 4 teeth for Mercedes-Benz.
1 pc Hex 32mm x 120mm x 4 tooth for MAN and Mercedes-Benz.
1 pc 1/2"Dr. x 120mm x 3 teeth for MAN and Mercedes-Benz.
Also suitable for some Iveco, Scania and Renault commercial vehicles.

Made in China

Mercedes Benz Ball Joint Remover Installer Set, 50453

Spesialized 10-Piece tool kit to service all of the pressed-in ball joints incorporated in the Mercedes W210 / W211 / W220 / W230 / W163/ W164 suspensions.
This tool set allows servicing (installation and removal) of the specified ball joints on the vehicle. This saves tremendous time and effort by avoiding the necessity of disassembling the brake system and other suspension components that would disturb suspension alignment.
Includes:
C-Clamp press tool forged (not cast) form SCM440 Steel (HRC 38-42 hardness)
Front Suspension Ball Joint press fixtures for W220 / W211 / W230 Chassis - used in Conjunction with the C-Clamp Press.
Front Sway Bar Ball Joint (pressed into control arm) press fixtures for W220 /
W211 - used in Conjunction with the C-Clamp Press.
Front & Rear Suspension Ball Joint press fixtures for W163 / W164 Chassis - used in Conjunction with the C-Clamp Press.
Ball joint socket (4-prong) for servicing front ball joint on W163 / W164 Chassis
Application: Mercedes Benz
W210 Chassis - 1995-2002 E Class
W211 Chassis - 2002-2009 E Class
W220 Chassis
W230 Chassis
W163 Chassis - 1998-2005 M Class
W164 Chassis - 2006-present M Class

Made in China

Adaptor +10 pcs Small Damage Repair Kit, 160-0211

The kit contains an adapter and 10 pcs removable pads, of different shapes and sizes, suitable for straightening small recesses in the car body.

Made in Taiwan

Magnetic tool holder, 50240
Removable magnetic multifunctional holder, which is mainly used for nuts or torque wrenches and impact sockets (17, 19, 21 mm).
Capacity: 9 kgs ( 20 Lbs )

Piston Ring Compressor 60-175 mm, 50091

With Safety valve Special spring steel
Ratchet type complete with hex spanner
Capacity: 60-175mm
Height: 150mm (6")

Made in China

Coil Spring Compressor For Wishbone Suspensions, 50452

Suitable to work on lower supports with a small access (< 30 mm)
Suitable for more coil springs - Working range: 95 - 220  mm
100Nm Extension torque bar controls excessive torque being applied
Holder discs with wide application
Applicable to vehicles with a swing arm diameter of 30 mm and bigger.
Applicable:
Chrysler, Citroen, Ford, Honda, KIA, Mitsubishi, Peugeot, Renault, Seat, Skoda, Suzuki, Toyota, Volvo, Volkswagen,  etc.
BMW 3 series (1996-2013)
Mercedes Benz W202/ W204 (1997-2013)
Includes:
150 mm steel pressure plate
130 mm steel pressure plate
Compressing bar
Extension bar with 100 Nm torque control for use with impact wrench.

Made in China

3/4" Dr. 17 mm 12-pt Impact deep socket, 50479

Material:  Cr-Mo
12-points
Deep:  110 mm
Applicable: For Mercedes trucks cylinder head screw.
For models MB400, MB420, MB500

Made in China

Windshield Removal Tool Set, 50220

This universal kit includes all of the specialised tools required to safely and quickly remove windshields from a wide variety of vehicles.
Item is supplied with a rubber gasket knife, cutting wire, two (2) handles, wire feeder tool, trim pad remover and molding release tool.

Set includes:

- Wire: Three strong galvanised steel wires braided to form one wire
- 2 pcs Wire gripping handles: Feed the wire through the hole in the wedge shaft. Loop it through the hole at the top of the shaft. Then back into the handle. Pressing the wedge back into the handle, the wire is held.
- Windshield removal tool: Cuts the vinyl adhesive compound around the windshield.
- Wire feeder tool: Designed for easy and flexible insertion of wire through polyurethane, allowing speedy removal of bonded windshield
- Trim pad remover: Place the tool under the edge of the door upholstery panel and insert it into the fastener as far as possible, then simply pry up.
1PC stainless steel wire with reel.
2PCS Wire gripping handles.
1PC Windshield removal tool
1PC Wire feeder tool
1PC Trim pad remover
1PC Windshield molding release tool

Made in China

Magnetic holder, 372-11050091

Made in Taiwan

18 pcs Universal caliper wind back set, 50060
• Provides both left-handed and right-handed thrust bolt assemblies
• Complete set of adaptors for a wide range of vehicle applications
• Designed for push back and wind back brake pistons
• Left-handed thrust bolt required for Ford, Citroen, and Renault applications
• Adaptor plates with thrust bolt assembly and reaction plate are precisely made
• Prevents damaging pistons and seals
• Updated adaptor set applicable for wide variety of vehicles"

VAG Cam Chain Tensioner Locking Tool, 058-62237
Compresses the camshaft chain tensioner safely and easily when removing camshafts or replacing the tensioner or its gasket. These tasks are virtually impossible without the correct tool.
The tool threads into the guide, compressing the tensioner, relieving chain tension.
The no-mar plastic contact surface will not harm the tensioner face.
Applicable:
Audi: A4, A6, A8, TT, S4, S6, RS6
Seat: Ibiza, Cordoba, Leon, Toledo, Alhambra
Skoda: Octavia
Volkswagen: Polo, Golf, Jetta, Passat, Beetle, Touareg
Engine Codes: ADR, AEB, AFY, AGN, AGU, AHA, AJE, AJH, AJL, AJP, AJQ, AMB, AMK, AMU, ANB, APB, APG, APH, APP, APT, APU, APX, ARH, ARK, ARX, ARY, ARZ, ATC, ATQ, AUM, AUQ, AVC, AWC, AWM, AWN, AWP, AWT, AWV, AYP, BAM, BBD, BCY, BEA, BEL, BFM, BKF, BNU
OEM №: 3366

Made in Taiwan

5 Pcs Ball Joint Separator, 50435

Content:
Ball Joint Separator
Tie Rod And Ball Joint Remover
Conical Pitman Arm Puller
Pitman Arm And Tie Rod End Puller
Pitman Arm Puller

Description:
Ball Joint Separator - For separating the ball joint from the spindle support arm on domestic and import front wheel drive vehicles adjustable for different size ball joints
1-1/8" & 2-1/8" (30 & 56mm) maximum opening capacity
7/8" jaw spread, 2-1/4" throat depth
Tie Rod And Ball Joint Remover - A universal heavy-duty puller that removes a wide range of tie rods and ball joints from a variety of cars, trucks, SUVs and heavy-duty vehicles.
0 to 2-1/2" jaw spread, 3-1/4" throat depth
Conical Pitman Arm Puller - Designed to fit securely on Pitman arms for compact and mid-size cars.
3/4-16 x 4-3/4" forcing screw provides enough power to remove stubborn pitman arms.
Pitman Arm And Tie Rod End Puller - This versatile tool can be used as a pitman arm remover for many small, domestic rear-wheel drive vehicles, or as a tie rod end puller for many domestic and import vehicles. The jaws, with a spread of 1", give a secure positive grip in tight workspaces.
1-1/8" jaw spread, 2-1/8" throat depth
Pitman Arm Puller - This puller will handle nearly any pitman arm job on passenger cars and light trucks. It features special forged jaws, shaped to fit most models, keeping a solid grip while you work.
1-11/32" jaw spread, 2-1/2" throat depth

Made in China

6 pcs 3/4" Dr. Impact deep socket, 50476

Material: Cr-Mo
Contents:
3/4" Dr. TORX Impact deep socket : E18, E20, E22, E24
3/4” Dr. 12-pt Impact deep socket: 17 mm, 19 mm

Made in China