INSTRUMENTS

Magnetic holder, 372-11050091

Made in Taiwan

18 pcs Universal caliper wind back set, 50060
• Provides both left-handed and right-handed thrust bolt assemblies
• Complete set of adaptors for a wide range of vehicle applications
• Designed for push back and wind back brake pistons
• Left-handed thrust bolt required for Ford, Citroen, and Renault applications
• Adaptor plates with thrust bolt assembly and reaction plate are precisely made
• Prevents damaging pistons and seals
• Updated adaptor set applicable for wide variety of vehicles

19 mm 1/2" Dr. Twist socket, 50927-19

Designed for removing damaged nuts and bolts, and especially for locking wheel nuts.
Material: Cr-Mo
1/2" Dr.
Size: 19 mm.

THE USE OF A IMPACT WRENCH IS NOT RECOMMENDED!

Made in China

Volvo 1.6, 1.9, 2.0, 2.4 - Diesel Engine Timing Tool Set 51030

Features: for Volvo 1.6, 1.9, 2.0 and 2.4 Diesel engines.
Applicable:  Volvo C30 (2006-2013), C70 (2006-2013), S40 (2004-2012), S60 (2001-2015), S80 (2001-2015), V40 (2000-2015), V50 (2004-2012), V60 (2010-2015), V70 (2001-2015), XC60 (2008-2015), XC70 (2002-2016), XC90 (2002-2014).
Engine codes:
1.6: D4164T, D4162T
1.9: D4192T3, D4192T4
2.0: D5204T2, D5204T3, D5204T5, D5204T, D4204T, D4204T2
2.4: D5244T9, D5244T13, D5244T8, D5244T5, D5244T6, D5244T7, D5244T, D5244T2, D5244T3, D5244T4, D5244T10, D5244T11, D5244T15, D5244T14, D5244T19, D5244T17, D5244T16, D5244T18

OEM# tools: 999 7119, 999 7120, 999 7121, 999 7120, 999 7233, 999 7122, 999 7005, 999 7007.

Made in China

Mercedes Benz Ball Joint Remover Installer Set, 50453

Spesialized 10-Piece tool kit to service all of the pressed-in ball joints incorporated in the Mercedes W210 / W211 / W220 / W230 / W163/ W164 suspensions.
This tool set allows servicing (installation and removal) of the specified ball joints on the vehicle. This saves tremendous time and effort by avoiding the necessity of disassembling the brake system and other suspension components that would disturb suspension alignment.
Includes:
C-Clamp press tool forged (not cast) form SCM440 Steel (HRC 38-42 hardness)
Front Suspension Ball Joint press fixtures for W220 / W211 / W230 Chassis - used in Conjunction with the C-Clamp Press.
Front Sway Bar Ball Joint (pressed into control arm) press fixtures for W220 /
W211 - used in Conjunction with the C-Clamp Press.
Front & Rear Suspension Ball Joint press fixtures for W163 / W164 Chassis - used in Conjunction with the C-Clamp Press.
Ball joint socket (4-prong) for servicing front ball joint on W163 / W164 Chassis
Application: Mercedes Benz
W210 Chassis - 1995-2002 E Class
W211 Chassis - 2002-2009 E Class
W220 Chassis
W230 Chassis
W163 Chassis - 1998-2005 M Class
W164 Chassis - 2006-present M Class

Made in China

3 Jaws Gea

3 Jaws Gear puller 8”, 50742D

Heat treated, forged alloy steel with rust-resistant.
Precision-machined, hardened and tempered, self-centering steel screw with black finish.
Zinc plated jaws and hardware.
Removes gears, pulleys, flywheels, etc, from shaft.
Applies even pressure to prevent damage.

Puller Size: 8”
Capacity: 80 – 203 mm

Made in China

r puller 8”, 50141-8

Air vacuum dent puller with 3 pads, 178-0169A

Contents:

3 pads: 75 mm, 100 mm, 125 mm

Working pressure: 5 - 12 Bar (70 - 170 Psi)

Made in Taiwan

21 pcs Universal Brake Caliper Wind Back Kit, 50061

Suitable for push back and wind back brake pistons.
Includes left- and right-handed thrust bolt assemblies.
Left-handed thrust bolt required for Ford, Citroen and Renault applications.
Adaptor plates with thrust bolt assembly and reaction plate.
Helps prevent damage to pistons and seals.
Updated adaptor set suitable for a wide variety vehicles. Supplied in carry-case.

17 mm 1/2" Dr. Twist socket, 50927-17

Designed for removing damaged nuts and bolts, and especially for locking wheel nuts.
Material: Cr-Mo
1/2" Dr.
Size: 17 mm.

THE USE OF A IMPACT WRENCH IS NOT RECOMMENDED!

Made in China

60-115mm Oil Filter Chain Wrench 50966

Designed for removing and installing oil filters.
Double chain provides powerful and smooth operation.
Capacity: Ø60-115mm.
1/2" Drive

Made in China

Coil Spring Compressor For Wishbone Suspensions, 50452

Suitable to work on lower supports with a small access (< 30 mm)
Suitable for more coil springs - Working range: 95 - 220  mm
100Nm Extension torque bar controls excessive torque being applied
Holder discs with wide application
Applicable to vehicles with a swing arm diameter of 30 mm and bigger.
Applicable:
Chrysler, Citroen, Ford, Honda, KIA, Mitsubishi, Peugeot, Renault, Seat, Skoda, Suzuki, Toyota, Volvo, Volkswagen,  etc.
BMW 3 series (1996-2013)
Mercedes Benz W202/ W204 (1997-2013)
Includes:
150 mm steel pressure plate
130 mm steel pressure plate
Compressing bar
Extension bar with 100 Nm torque control for use with impact wrench.

Made in China

3 Jaws Gear puller 10”, 50742E

Heat treated, forged alloy steel with rust-resistant.
Precision-machined, hardened and tempered, self-centering steel screw with black finish.
Zinc plated jaws and hardware.
Removes gears, pulleys, flywheels, etc, from shaft.
Applies even pressure to prevent damage.

Puller Size: 10”

Made in China

35 pcs Universal caliper wind back set, 50064

Suitable for push back and wind back brake pistons.
Includes left- and right-handed thrust bolt assemblies.
Left-handed thrust bolt required for Ford, Citroen and Renault applications.
Adaptor plates with thrust bolt assembly and reaction plate.
Helps prevent damage to pistons and seals.
Updated adaptor set suitable for a wide variety vehicles. Supplied in carry-case.

Manual operation dent puller with 10 pcs glue pads, 160-3113

Perfect hand tool for repairing small dents on the vehicle compartment.

Contains: Adjustable clamp with plastic protectors and aluminum housing and 10 pcs. removable pads.
Rotating pads provide stability when working on non-linear surfaces.

How it works can be seen in the following video:

Made in Taiwan

12 mm 1/2" Dr. Stud Extractor, 50922-12

Designed for removing studs without damaging the threads.
Safe clamping due to 3 rollers. The extractors are the concentric roller bearing type that won't damage the thread on the stud.
Material: Cr-V
1/2" Drive (Hex 21mm).
Size: 12 mm.

Made in China