INSTRUMENTS

3 Jaws Gear puller 12”, 50742F

Heat treated, forged alloy steel with rust-resistant.
Precision-machined, hardened and tempered, self-centering steel screw with black finish.
Zinc plated jaws and hardware.
Removes gears, pulleys, flywheels, etc, from shaft.
Applies even pressure to prevent damage.

Puller Size: 12”

Made in China

19 mm 1/2" Dr. Twist socket, 50927-19

Designed for removing damaged nuts and bolts, and especially for locking wheel nuts.
Material: Cr-Mo
1/2" Dr.
Size: 19 mm.

THE USE OF A IMPACT WRENCH IS NOT RECOMMENDED!

Made in China

Mercedes Benz Ball Joint Remover Installer Set, 50453

Spesialized 10-Piece tool kit to service all of the pressed-in ball joints incorporated in the Mercedes W210 / W211 / W220 / W230 / W163/ W164 suspensions.
This tool set allows servicing (installation and removal) of the specified ball joints on the vehicle. This saves tremendous time and effort by avoiding the necessity of disassembling the brake system and other suspension components that would disturb suspension alignment.
Includes:
C-Clamp press tool forged (not cast) form SCM440 Steel (HRC 38-42 hardness)
Front Suspension Ball Joint press fixtures for W220 / W211 / W230 Chassis - used in Conjunction with the C-Clamp Press.
Front Sway Bar Ball Joint (pressed into control arm) press fixtures for W220 /
W211 - used in Conjunction with the C-Clamp Press.
Front & Rear Suspension Ball Joint press fixtures for W163 / W164 Chassis - used in Conjunction with the C-Clamp Press.
Ball joint socket (4-prong) for servicing front ball joint on W163 / W164 Chassis
Application: Mercedes Benz
W210 Chassis - 1995-2002 E Class
W211 Chassis - 2002-2009 E Class
W220 Chassis
W230 Chassis
W163 Chassis - 1998-2005 M Class
W164 Chassis - 2006-present M Class

Made in China

10-32mm 1/2"Dr. 12-pt 15 pcs Flank deep socket set, C4151-9

Material: Cr-V

Contents: 10; 11; 12; 13; 14; 15; 16; 17; 19; 21; 22; 24; 27; 30; 32 mm

Produced by Pard, Taiwan

Adaptor +10 pcs Small Damage Repair Kit, 160-0211

The kit contains an adapter and 10 pcs removable pads, of different shapes and sizes, suitable for straightening small recesses in the car body.

Made in Taiwan

Vacuum tester and brake bleeder, 50411

The Vacuum/Pressure Pump may be used for many different tasks.
1. Testing vacuum-operated components (door locks, actuators,etc)
2. Engine mechanical testing (valves, cam timing, head gasket, etc)
3. Brake and clutch hydraulic system bleeding
4.Measurement of vacuum supplied by booster reservoirs solenoids or the engine.
Features:
Checks vacuum/pressure
Operated automotive components.
Can be used to bleed hydraulic  systems or siphon fluids.
Detailed used instructions and photos inside of case.
Hand pump with built-in vacuum pump
Assorted vacuum hoses
Assorted hose adapters
Universal cup adapter
4 ounce reservoir jar
Jar lids

8 pcs Timing Locking Tool Set, 50088

For Locking and Setting Timing when replacing timing belts

Suitable for: Opel, VW, Audi, Skoda, Seat, Ford, Citroen, FIAT, Peugeot, Isuzu, Saab und Rover

Contents:
Flywheel locking tool Citroen: 2.0 petrol engines, Peugeot: 1.6, 2.0 petrol engines, 2.0, 2.1 TD engines
Crankshaft locking tool Audi: 1.2. 1.4, 1.9, 2.0 TDI PD, Seat: 1.4, 1.9, 2.0 TDI PD, Skoda: 1.4, 1.9, 2.0 TDI PD, VW: 1.4, 1.9, 2.0 TDI PD, 2.0 SDI
Camshaft locking tool Rover: 1.4, 1.6, 1.8 V16 engines
Twin camshaft locking tool Opel: 1.6 CNG, 1.6 V16, 1.8i, 1.4, 1.6, 1.8 petrol engines
Twin camshaft locking tool Opel: 2.0 OPC/VXR, 2.0 Turbo, 1.8 V16, 2.0, 2.2 petrol engines
Flywheel locking tool Opel: 1.2, 1.4, 1.6 petrol engines, 1.7 TD, 1.6, 1.7 D engines
Camshaft locking tool Opel: 2.5, 2.6, 3.0, 3.2 V6, 2.5, 2.6 V6i, Saab: 2.5, 3.0 V6 engines
Camshaft locking tool Opel: 2.5, 2.6, 3.0, 3.2 V6, 2.5, 2.6 V6i, Saab: 2.5, 3.0 V6 engines

Models:
Citroen: Jumper
Peugeot: 406, 605, 806
Audi: A2, A3, A4, A4 Quattro, A6, A6 Quattro
Seat: Alhambra, Arosa, Cordoba, Ibiza, Leon, Toledo
Skoda: Octavia, Roomster, Superb
VW: Beetle, Bora, Caddy, Caddy Maxi, Golf, Jetta, Passat, Polo, Sharan, Tiguan, Touran, Transporter
Rover: 111, 114, 211, 214, 214/216 Cabrio, 216 V16 Coupe, 218, 414, 416, 25, 45, 75, Metro, VVC, MGF, TF
Opel: Astra -F, -G, -H, Combo, Corsa -A, Calibra, Meriva, Signum, Tigra, Vectra -B, -C, Zafira -A, -B, Frontera -A, -B, Omega -B, Speedster, Kadett, Cavallier, Ascona -C, Sintra
Saab: 900, 9000, 9-5

Engine code:
Citroen: RTZ
Peugeot: XU10J2CTE, XUD11BTE, XU5JP, XUD11BTE, XU10J2TE/Z, XUD11BTE, XU10J2C/Z
VAG: ANY, ATL, BHC, AMF, BKC, ASZ, ATD, AXR, AVB, AVF, AWX, ATJ, AJM, BNA, BRF, BVF, BVG, BLB, BRE, BVA, BRD, AUY, BTB, BVK, ANU, BJB, BKC, AZV, BKD, BMN, BMS, BNV, BMT, BPX, BUK, BLT, BXE, ARL, BMM, BSW, BZS, BLS, AWB, BSU, BDJ, BST, AYZ, BRU, BGW, BHW, BMA, BUZ, BVE, BWV, BMP, BMR, BKP, BAY, BWB, AXR, BVK, BXF, AVQ, AXC, BRR, AXB
Opel: Z18XE, X18XE1, X18XE, Z18XEL, Z16YNG, X14XE, Z14XE, X16XEL, Z16XE, Y16XE, X16SEJ, X18E1, X20XEV, Z20LEH, Z20LER, Z20LEL, X22XE, X22SE, Y22SE, Y22XE, Z22XE, C20SEL, X20EV, Z20LET, 16DA, 17DA, E14LV, C14NZ, 14NV, C16NZ, E16NZ, C16LZ, 16SV, C16NZ2, X16SZ, 17DR, 12NV, C12NV, C14SE, C14SEL, C16SEL, E14LV, C16SE, X17DTL, X25XE, X30XE, Y26SE, Y32SE

Made in China

17 mm 1/2" Dr. Twist socket, 50927-17

Designed for removing damaged nuts and bolts, and especially for locking wheel nuts.
Material: Cr-Mo
1/2" Dr.
Size: 17 mm.

THE USE OF A IMPACT WRENCH IS NOT RECOMMENDED!

Made in China

Ford - Torque Multiplier Set, 51201

Features: To remove and install the crankshaft pulley bolt, in order to replace the timing belt.
Suitable for Ford 1.0 Ecoboost, 1.0 / 1.1 Duratec, 2.0 EcoBlue and 2.0 Duratorq-TDCi engine.

Max. torque input: 300Nm.
Max. torque output: 1500Nm.
Gear ratio: 1:5.
Input drive: 1/2".
Output drive: 3/4".

Applicable:
Ford B-MAX, C-MAX, EcoSport, Fiesta, Focus, Mondeo, Grand Tourneo Connect, Tourneo Connect, Transit Connect, Transit Courier

OEM# tools: 303-1611, 303-1611-01, 303-1611-02.

Made in China

Coil Spring Compressor For Wishbone Suspensions, 50452

Suitable to work on lower supports with a small access (< 30 mm)
Suitable for more coil springs - Working range: 95 - 220  mm
100Nm Extension torque bar controls excessive torque being applied
Holder discs with wide application
Applicable to vehicles with a swing arm diameter of 30 mm and bigger.
Applicable:
Chrysler, Citroen, Ford, Honda, KIA, Mitsubishi, Peugeot, Renault, Seat, Skoda, Suzuki, Toyota, Volvo, Volkswagen,  etc.
BMW 3 series (1996-2013)
Mercedes Benz W202/ W204 (1997-2013)
Includes:
150 mm steel pressure plate
130 mm steel pressure plate
Compressing bar
Extension bar with 100 Nm torque control for use with impact wrench.

Made in China

10-24 mm 1/2"Dr. 6-pt. Flank impact deep socket set, C4112

Material: Cr-Mo

Over: 85 mm

Contents:

10; 11; 12; 13; 14; 15; 17; 19; 21; 22; 24 mm

Produced by Pard, Taiwan

Windshield Removal Tool Set, 50220

This universal kit includes all of the specialised tools required to safely and quickly remove windshields from a wide variety of vehicles.
Item is supplied with a rubber gasket knife, cutting wire, two (2) handles, wire feeder tool, trim pad remover and molding release tool.

Set includes:

- Wire: Three strong galvanised steel wires braided to form one wire
- 2 pcs Wire gripping handles: Feed the wire through the hole in the wedge shaft. Loop it through the hole at the top of the shaft. Then back into the handle. Pressing the wedge back into the handle, the wire is held.
- Windshield removal tool: Cuts the vinyl adhesive compound around the windshield.
- Wire feeder tool: Designed for easy and flexible insertion of wire through polyurethane, allowing speedy removal of bonded windshield
- Trim pad remover: Place the tool under the edge of the door upholstery panel and insert it into the fastener as far as possible, then simply pry up.
1PC stainless steel wire with reel.
2PCS Wire gripping handles.
1PC Windshield removal tool
1PC Wire feeder tool
1PC Trim pad remover
1PC Windshield molding release tool

Made in China

Vacuum pressure pump brake bleeding kit, 50404A

Easily bleed brakes and test automotive vacuum systems by yourself
Works on all vehicle makes and models
Replaceable O-ring cylinder head gasket, rubber piston ring and valves
Precise pressure gauge: 0 -30inHg, 0 -760mmHg 

Made in China

12 mm 1/2" Dr. Stud Extractor, 50922-12

Designed for removing studs without damaging the threads.
Safe clamping due to 3 rollers. The extractors are the concentric roller bearing type that won't damage the thread on the stud.
Material: Cr-V
1/2" Drive (Hex 21mm).
Size: 12 mm.

Made in China

Jaguar, Land Rover 2.0 - Diesel Engine Timing Tool, 50558

Application: on Jaguar F PACE, XE, XF (2015 Onwards). Land Rover, Discovery Sport, Range Rover Evoque(2015 Onwards).

Engine codes: AJ-200D, 204DT, AJ200D, AJ200, 204DTD.

OEM# 303-1625, 303-1631, 303-1630, 303-1627

Made in China