ENGINE TIMING TOOLS

BMW N47 N57 Crankshaft Locking Tool, 50728

It’s difficult to replace the oil pump chain, both timing chains, the gear of the high pressure pump and of the balancer shaft if without this locking tool.
Without this tool the engine works irregularly.

• Applications: BMW 2.0 N47 & 3.0 N57 diesel engines.

• OEM Code: 114 320.

The crankshaft must be blocked in order to release central bolt of the high pressure pump. Position special tool with screw at the crankcase. Release central bolt of high pressure pump.

Important! Release central bolt only, do not remove.

Used on the following Vehicles:
BMW 1 Series 2007 - 2015 EfficientDynamics
BMW 2 Series 2014 - 2016 114d/116d/118d/120d/123d
BMW 3 Series 2007 - 2017 125d/218d/220d/225d
BMW 4 Series 2013 - 2017 316d/318d/320d/325d/330d
BMW 5 Series 2007 - 2017 320d EfficientDynamics
BMW 6 Series 2011 - 2017 420d/425d/418d/520d
BMW 7 Series 2008 - 2015 518d/525d/530d/535d
BMW X1 2009 - 2015 520d GT/530d GT
BMW X3 2007 - 2017 d
BMW X5 2012 - 2017 640d/730d
BMW X4 2014 - 2017 xDrive
BMW X5 2010 - 2017 sDrive
BMW X6 2010 - 2017 M550d/750d/M50d
BMW X6 2010 - 2017 xDrive
Engine Codes:
1.6cc
N47 D16C N47 D16
2.0cc
N47 D20A/K0 N47 D20A N47S D20B/D/T0 N47 D20C/K1 N47 D20C N47 D20C/U1 N47 D20C/O1 N47 D20D N47 D20D/T1 N47 D20A/U0 N47T D20K1 N47 D20U0 N47T D20U1 N47T D20O1 N47 D20C/O N47 D20C/01 N47 D20O0 N47S D20D/T0 N47 D20A/O0
3.0cc
N57 D30U0 N57 D30A/O0 N57 D30A/O1 N57 D30B N57 D30A N57 D30UO N57 D30O0 N57 D30O1 N57 D30B/T1 N57 D30TO N57 D30A0/O0 N57 D30T0 N57 D30B/T0 N57 D30C/S1 N57 D30C

Timing Tool set for Petrol Citroen C3 Peugeot 208, 308, 2008 SUV, Psa 1.0 1.2 Vti, 780-8331

To check and adjust the camshaft and crankshaft in the correct TDC position.
Applicable: Peugeot 208 (2008); 2012 Citroen C3
Engine code: 1.0, 1.2 VTi petrol engine: EBO (ZMZ), EB2 (HMZ)
OEM number: 0109-2A, 0109-2B

Made in Taiwan

VAG with 1.6 TDi engines - Diesel injector remover, 011108019
Applicable: Engines: 1.6L CRTD diesel.
OEM Tools: T10402, T10055.
Use according to OEM instructions.
No solenoid removal is required.

Made in Taiwan

BMW N62; N73 Camshaft alignment tool set, 50734

Main set of chain synchronization tools for 3.6; 4.0; 4.4; 4.8; 6.0 V8 engines. Designed for BMW N62 V8 and N73 V12 engines.
The kit has all the necessary tools to lock and hold the crankshaft and crankshaft in their correct synchronization positions.
Contents:
1. Inlet Camshaft Gauge (11 9 461)
2. Exhaust Camshaft Gauge (11 9 462)
For positioning the camshaft at the TDC position (top dead center) for checking and adjusting the synchronization.
Application: BMW N62, N62TU, N73, E53, E60, E61, E63, E64, E65
3. Bracket with bolt (11 9 463)
To check and adjust the camshaft when synchronizing.
Application: BMW N62, N62TU, N73
4. Camshaft alignment pin. (11 9 190)
To block the flywheel at the TDC position (top dead center).
Application: BMW N40, N42, N62, N62TU, N73
5. Chain tensioner (11 9 340)
For tension primary chain and Short format for new generation new generation engines.
Application: BMW N40, N42, N45, N46, N52, N62
6. Left cylinder head socket (11 7 270)
For disassembly and assembly left cylinder head.
Application: BMW N73
7. Gasket and Bolt (11 9 452)
Application: BMW N62, N62TU, N73
8. Fixing Crankshaft wrench (11 9 451)
It works with a 27 mm socket  and serves for the removal and installation of the crankshaft.
Application: BMW N62, N62TU, N73
9. Angle indicator (11, 9, 453)
Indicates the angle of the gauge and uses 27mm Socket to fix this tool.
Application: BMW N62, N62TU, N73
10. 27 mm socket (11 9,454)
Application: BMW N62, N62TU, N73
11. Gauge Angle Position (11 3 460)
Graduated disc for torque center bolt.
Application: BMW M60, M62, M73, N62, N62TU, N73
ОЕМ Tools No.:
 11 3 460, 11 7 270, 11 9 190, 11 9 340, 11 9 451, 11 9 452, 11 9 453, 11 9 454, 11 9 461, 11 9 462, 11 9 463
Applicable: For diesel and petrol engines fitted to: 540i, 545i, 550i, 645i, 650i, 735i, 740i, 745i, 750i, X5.
2001-2009 3.6~4.8 Liter V8 N62 с SFI fuel injection, Double-VANOS и Valvetronic 2003-2009 6.0 Liter V12 N73.

Made in China

Diesel/Petrol Engine flywheel holding tool -  BMW/BMW Mini – Chain drive, 50657

Basic tool for fixing the flywheel when releasing and tightening the vibration damper central bolts on BMW M47T2, M57T2, M57TU, M67, N20, N26, N43, N45, N45, N46, N47, N51, N52, N53, N54 W17 Diesel and Petrol chain drive engines.
It can also be used to fix the flywheel when dismantling the timing chain for cylinder head work.
Applicable:
BMW 1 Series: (F20/21) (12-15), 116i (04-12), 118i (04-14), 120i (04-14), 130i (05-07), 135i (07-11), 116d (08-12), 118d (04-14), 120d (04-14), 123d (07-14), M Coupe (11-12)
BMW 3 Series: (F30/31) (12-15), 316ti (04-14), 316i (04-11), 316d (09-12), 318i (04-07), 318ti/Compact (04-04), 318d (03-12), 318td (03-07), 320d (01-07), 320d Compact (01-05), 318i (05-13), 320d (07-14), 320i (05-14), 320si(05-06), 323i (05-11), 325i (05-14), 325d (06-10), 330d (05-08), 330i (06-13), 335d (05-13), 335i (05-11)
 BMW 4 Series: 420i F32 (13-15), 428i F32 (13-15), 420i F33 Cabriolet (14-15), 428i F33 Cabriolet (14-15), 420i F36 (14-15), 428i F36 Gran Coupe (14-15)
BMW 5 Series: (F10/11) (10-15), 520d (05-10), 520i (07-10) 523i (03-10), 525d (05-10), 525i (05-10), 525i (07-10), 530d (03-10), 530i (05-10), 535d (04-10)
BMW 6 Series: 630i (04-11), 635d (07-11)
BMW 7 Series: 730d (05-08), 730i (02-08)
BMW X Series: X1 E84 (09-15), X3 E83 (03-14), X5 E53 (03-14), X3 F25 (11-15), X6 E71/72 (08-10)
BMW Z Series: Z4 E85/86 (04-09), Z4 (E89) (11-15)
BMW Mini: Mini (03-06)
Engine codes:
BMW: M47T2, M57T2, M57TU, M67, N20, N26, N43, N45, N45T, N46, N46T, N47, N51, N52, N53, N54
BMW Mini: W17
Инструменти по OEM:
BMW: 11.8.180, 11.8.181, 11.8.182, 11.8.183, 11.8.184, 11.8.185

Timing tool set for FIAT 2.2; 2.3; 3.0 JTD and 22DT PSA engines, 50601
Used for belt timing as well as chain-driven engines, including later versions, for light commercial vehicles with 2.2; 2.3; 3.0 and PSA engines.
The set contents a water sensor installation socket, crankshaft turning tool, timing cover centring plate, oil pump setting plate as well as camshaft and crankshaft locking tools.
These engines are also found in the Ford Transit.
OEM Tools No:
Fiat / Iveco: 1.860.617.000/99360608, 2.000.016.500/99360614, 2.000.018.200/99360615
Citroen / Peugeot: 0191 / 2A, 0191 / 2B, 0198A, 0198B2, 0198D, 0198G
Ford: 303-698, 303-705 / 21-256
Applicable:
Citroen: Relay/Jumper III (06-12)
Fiat: Ducato (02-13)
Iveco: Daily (03-10), Daily/EcoDaily (09-11)
Пежо: Boxer III (06-12)
Also suitable for PSA engines:
  - Puma 22DT 4HV 100PS
  - Puma 22DT 4HV 120PS
  - F30DT
Engine code:
Citroen / Peugeot:
2.2D Hdi: 4HM, 4HM, 4HV
Fiat:
2.2D Multijet 100: 4HV
2.3D JTD: F1AE0481C
2.3D Multijet: F1AE0481D, F1AE0481N, F1AE3481E
3.0D Multijet: F1CE0481D, F1CE3481E, FCE13481M, F1CE3481N
Iveco:
2.3D: F1AE0481A, F1AE0481G, F1AE0481GA, F1AE0481H, F1AE0481HA, F1AE0481R, F1AE0481RA, F1AE0481UA, F1AE0481VA
3.0D: F1CE0481A, F1CE0481B, F1CE0481F, F1CE0481H

Made in China

Engine timing tool kit - OPEL/Vauxhall 2.0 CDTI, 50171

Designed for: To removal and replace the Opel / Vauxhall 2.0 CDTi camshaft drive belt. The kit also includes flywheel locking tools for vehicles equipped with an automatic transmission.
Applicable: Opel / Vauxhall 2.0 CDTi - LFS / B20DTH, LFS / B20DTR (2.0 CDTi от 2014 г.).
Models: Antara (от 2016 г.), Cascada (от 2015 г.), Insignia-A / Country Tourer (2014-2017), Insignia-B / Country Tourer (от 2017 г.) и Zafira-C Tourer (от 2014 г.); CDTi EcoFLEX Blueinjection
OEM tool No.: EN 51413, EN 955-2, EN 51412, EN 51414, EN 51411

Made in China

Setting Tool Kit 1.0 Turbo 3 Cylinder Petrol Engine for Ford, 50170

Introduced in 2011, Ford 1.0 turbo, 3 cylinder, Ecoboost (SCTi) petrol engine fits in the various car and light commercial vehicle across Ford range.
The engine features a wet timing belt (belt in oil) that runs between the crankshaft and the twin camshaft VVT sprocket.
The timing belt is a conventional arrangement, the exception is being that the belt is encases in the engine and runs in oil in a similar set-up as a chain engine.
Contents:
Camshaft Locking Tool Set.
Camshaft VVT Adjustment Tool Set.
Crankshaft Setting Pin.
Flywheel Locking Tool.
Tensioner Locking Pin.
Crankshaft Pulley Positioning Pin.
OEM tool No.: 303-1606, 303-1605, 303-1604, 303-1602, 303-1054, 303-732.
Applicable: 
C-MAX, Focus, Grand C-MAX, EcoSport, Fiesta, B-MAX, Tourneo Connect, Transit Connect.
Engine codes: 
M1DA, M2DA, M1JC, M1JE, SFJA, SFJB, M2GA, P4JA, P4JB, XMJA, XMJB.

BMW N20 N26 Engine timing tool set, 50125

The kit includes a set of tools needed to timing the newer BMW N20, N26 4-cylinder turbo engine.
OEM tools: 212 831, 119 340, 212 830 and 219 548
Content:
Tool for locking the camshaft for N20 / N26
N20 / N26 camshaft fixing base
Aligning pin for N20 / N26
Chain tensioner for N40, N42, N45, N46, N52, N55, N62
Application:
Engine N20 and N26 (4 cylinder turbo engine)
2011-present E84 X1 xDrive/sDrive20i
2011-present F25 X3 xDrive20i
2012-present F30 320i
2013-present F34 320i GT
2012-present F10 520i
2011-present E89 Z4 sDrive20i
2012-present F20 125i
2011-present E89 Z4 sDrive28i
2011-present E84 X1 xDrive/sDrive28i
2012-present F25 X3 xDrive28i
2011-present F30 328i
2012-present F10 528i
2013-present F34 328i GT
Engine Codes: 2.0: N20 B20, N20 B20A, N20 B20O0, N20 B20B / U0, N20 B20B, N26 B20, N26 B20A

BMW N63/S63 Camshaft alignment tool set,  50118

Features:
Special designed to fixing the camshaft in TDC position. Checking and adjusting the timing chain tensioner.
Application:
For BMW N63 engine (After Sep. 2012)
For BMW S63 Engine:
S63B44O0
E70 X5M (2010-2013)
E71 X6M (2010-2013)
Wiesmann GT MF5 (2011-present)
S63B44T0
F10 M5 (2011-present)
F12 M6 (2012-present)
F13 M6 (2012-present)
F06 M6 Gran Coupe (2013-present).
OEM Number:
    83302249117 (#2249117)
    83302249140 (#2249140)
    83302249144 (#2249144)
    83302249159 (#2249159)
    83302249162 (#2249162)
    11 8 570 Vibration Damper Lock
    11 9 190 Plug Mandrel / Timing Pin

Made in China

Valve spring compressor lever type OHV/OHC engines, 50117

Suitable for replace springs and valve stem oil seals.
It is not necessary to remove the cylinder head.
With its adjustable handle, claws and hooks, the tool can be used on most OHV / OHC engines.
Applicable to two-shaft drive engines.
Can be used in hard-to-reach places.
Made of high-grade steel No. 50.
N.W.: 700 g

Mercedes M651 Camshaft locking tool kit, 50058

Features:
To lock and hold the camshaft and balance shaft in the timed position.
Also for turning, disassembly  and installing the crankshaft pulley.
Applicable:
Mercedes-Benz OM651 1.8/2.1/2.2 CDI diesel engines  - Chain drive:
Mercedes-Benz: A-Class, B-Class, C-Class Coupe, C-Class Cabriolet, E-Class, E-Class Coupe, E-Class Cabriolet, CLA Coupe, CLA Shooting Brake, CLS, GLA, GLC, GLC Coupe, GLE, GLK, M-Class, S-Class, SLC, SLK, Sprinter, Valente, V-Class, Viano, Vit.
Jeep: Compass, Patriot.
Engine codes:
1.8: 651.901
2.1: 651.930, 651.921, 651.960, 651.913, 651.916, 651.912, 651.961, 651.980, 651.9, 651.956, 651.955, 651.957, 651.950, 651.940, 651.910, 651.911, 651.924, 651.925, 651.922, 651.911, 651.924
2.2: 651.925, ENE (651.925)
No. по OEM: 651 589 09 40 00; 651 589 00 40 00; 651 589 02 63 00.

DSG Clutch Instalation set – VAG, 50842

Designed for the correct removal and installer of twin plate clutches used in VAG 6/7 speed gearboxes as featured in Volkswagen Golf / Touareg и Audi A3
Applicable: VW GOLF (2004 onwards), VW TOUAREG (6 speed) and AUDI A3 (2004 onwards).
Inclded the equivalent to OEM tools:
T10323 - Clutch support device
T10373 – Clitch puller
T10374 – Release bearing setting tool
T10376 – Clutch press piece.

Engine Crankshaft Pulley Remover Tool Set-Jaguar-Land Rover V8-Chain Drive, 50821

Special designed for pulley removal and holding tools.
Appicable: New Range Rover, Range Rover Sport, Discovery 3, Jaguar XJ8, XJR, S Type, XF, XK8, XKR.
Suitable for Jaguar and Land Rover 3.2, 3.5, 4.0, 4.2, 4.4 V8 petrol engines.
Land Rover 3 / Discovery 3 V8 4.4L | '05 - '09 | 4.4 V8 Engine Only
Range Rover Full Size 4.4 (Jag Engine) | '06 - '09 | JAG V8 ENGINE
Range Rover Full Size 4.2 Supercharged (Jag Engine) | '06 - '09 | JAG V8 ENGINE
Range Rover Sport | '06 - '09
Range Rover Sport Supercharged | '06 - '09

Made in China

Petrol Engine setting/locking set – Opel/Vauxhall, Chevrolet 1.0; 1.2, 1.4, 50750

Feature: For checking and setting the camshaft and crankshaft in correct TDC position.
Covers a wide range of Vauxhall/Opel and Chevrolet petrol engines. Includes the necessary tools for setting and locking the camshafts and crankshaft. Also includes the pins for locking the timing chain tensioner.
Contents:
Crankshaft Locking Pin
Camshaft Setting Plate
VVT Sensor Setting Tool (1.0L)
VVT Sensor Setting Tool (1.2 & 1.4L)
Camshaft Sprocket Holding Tool
Chain Tensioner Locking Pin
Belt Tensioner Locking Pin
Applicable:
For Vauxhall / for Opel :
Adam 1.2 1.4 (2012- ), Ampera 1.4 (2011- ),
Astra-J 1.4 (2009),
Corsa-D 1.0 1.2 1.4 (2009-),Cascada 1.4 (2013-),
Insignia 1.4 (2011-), Meriva-B 1.4 (2010-),
Mokka 1.4 (2012-), Zafira-C Tourer  1.4 (2011-)
For Chevrolet:
Aveo1.2 1.4 (2011-), Cruze 1.4 (2011-), Orlando 1.4 (2012-)
Engine Codes:
1.0/1.0 Ecoflex: A10XEP
1.2/1.2 Ecoflex: A12XEL, A12XER, LWD/A12XEL, L2Q/A12XEL, LDC/A12XER
1.4/1.4 Ecoflex: A14XER, LDD/A14XEL, LDD/A14XER, LUH/A14NEL, LUJ/A14NEL, LUJ/A14NET

Made in : China