UNDER CAR TOOLS

SCANIA - 80mm 8-pt. Front Hub Nut Socket, TP9T1422
Description:
This eight sided 80mm socket is designed for the removal of front hub nut found on Scania trucks.
Lenght: 104 mm
Innerdiameter: 80 mm
Outerdiameter: 100 mm
Driven by 41mm Hex
Weight: 1800 gr

Made in Taiwan

Mercedes Benz Ball Joint Remover Installer Set, 50453

Spesialized 10-Piece tool kit to service all of the pressed-in ball joints incorporated in the Mercedes W210 / W211 / W220 / W230 / W163/ W164 suspensions.
This tool set allows servicing (installation and removal) of the specified ball joints on the vehicle. This saves tremendous time and effort by avoiding the necessity of disassembling the brake system and other suspension components that would disturb suspension alignment.
Includes:
C-Clamp press tool forged (not cast) form SCM440 Steel (HRC 38-42 hardness)
Front Suspension Ball Joint press fixtures for W220 / W211 / W230 Chassis - used in Conjunction with the C-Clamp Press.
Front Sway Bar Ball Joint (pressed into control arm) press fixtures for W220 /
W211 - used in Conjunction with the C-Clamp Press.
Front & Rear Suspension Ball Joint press fixtures for W163 / W164 Chassis - used in Conjunction with the C-Clamp Press.
Ball joint socket (4-prong) for servicing front ball joint on W163 / W164 Chassis
Application: Mercedes Benz
W210 Chassis - 1995-2002 E Class
W211 Chassis - 2002-2009 E Class
W220 Chassis
W230 Chassis
W163 Chassis - 1998-2005 M Class
W164 Chassis - 2006-present M Class

Made in China

Coil Spring Compressor For Wishbone Suspensions, 50452

Suitable to work on lower supports with a small access (< 30 mm)
Suitable for more coil springs - Working range: 95 - 220  mm
100Nm Extension torque bar controls excessive torque being applied
Holder discs with wide application
Applicable to vehicles with a swing arm diameter of 30 mm and bigger.
Applicable:
Chrysler, Citroen, Ford, Honda, KIA, Mitsubishi, Peugeot, Renault, Seat, Skoda, Suzuki, Toyota, Volvo, Volkswagen,  etc.
BMW 3 series (1996-2013)
Mercedes Benz W202/ W204 (1997-2013)
Includes:
150 mm steel pressure plate
130 mm steel pressure plate
Compressing bar
Extension bar with 100 Nm torque control for use with impact wrench.

Made in China

5 Pcs Ball Joint Separator, 50435

Content:
Ball Joint Separator
Tie Rod And Ball Joint Remover
Conical Pitman Arm Puller
Pitman Arm And Tie Rod End Puller
Pitman Arm Puller

Description:
Ball Joint Separator - For separating the ball joint from the spindle support arm on domestic and import front wheel drive vehicles adjustable for different size ball joints
1-1/8" & 2-1/8" (30 & 56mm) maximum opening capacity
7/8" jaw spread, 2-1/4" throat depth
Tie Rod And Ball Joint Remover - A universal heavy-duty puller that removes a wide range of tie rods and ball joints from a variety of cars, trucks, SUVs and heavy-duty vehicles.
0 to 2-1/2" jaw spread, 3-1/4" throat depth
Conical Pitman Arm Puller - Designed to fit securely on Pitman arms for compact and mid-size cars.
3/4-16 x 4-3/4" forcing screw provides enough power to remove stubborn pitman arms.
Pitman Arm And Tie Rod End Puller - This versatile tool can be used as a pitman arm remover for many small, domestic rear-wheel drive vehicles, or as a tie rod end puller for many domestic and import vehicles. The jaws, with a spread of 1", give a secure positive grip in tight workspaces.
1-1/8" jaw spread, 2-1/8" throat depth
Pitman Arm Puller - This puller will handle nearly any pitman arm job on passenger cars and light trucks. It features special forged jaws, shaped to fit most models, keeping a solid grip while you work.
1-11/32" jaw spread, 2-1/2" throat depth

Made in China

M16x2.5 Spindle for Press and Pull Sleeve Kit, 50093-4

Pulling spindle with nuts and thrust bearings.

Size: M16x2.5 mm

Length: 450 mm

Material: carbon steel

Made in China

M14x2.0 Spindle for Press and Pull Sleeve Kit, 50093-3

Pulling spindle with nuts and thrust bearings.

Size: M14x2.0 mm

Length: 450 mm

Material: carbon steel

Made in China

M12x2.0 Spindle for Press and Pull Sleeve Kit, 50093-2

Pulling spindle with nuts and thrust bearings.

Size: M12x2.0 mm

Length: 450 mm

Material: carbon steel

Made in China

M10x1.5 Spindle for Press and Pull Sleeve Kit, 50093-1

Pulling spindle with nuts and thrust bearings.

Size: M10x1.5 mm

Length: 450 mm

Material: carbon steel

Made in China

M18x2.5 Spindle for Press and Pull Sleeve Kit, 50092-5

Pulling spindle with nuts and thrust bearings.

Size: M18x2.5 mm

Length: 350 mm

Material: carbon steel

Made in China

M160x2.5 Spindle for Press and Pull Sleeve Kit, 50092-4

Pulling spindle with nuts and thrust bearings.

Size: M16x2.5 mm

Length: 350 mm

Material: carbon steel

Made in China

M14x2.0 Spindle for Press and Pull Sleeve Kit, 50092-3

Pulling spindle with nuts and thrust bearings.

Size: M14x1.5 mm

Length: 350 mm

Material: carbon steel

Made in China

M12x2.0 Spindle for Press and Pull Sleeve Kit, 50092-2

Pulling spindle with nuts and thrust bearings.

Size: M12x2.0 mm

Length: 350 mm

Material: carbon steel

Made in China

M10x1.5 Spindle for Press and Pull Sleeve Kit, 50092-1

Pulling spindle with nuts and thrust bearings.

Size: M10x1.5 mm

Length: 350 mm

Material: carbon steel

Made in China

28 pcs Press and sleeve master kit, 50605

Ideally for silent bearings, hydro bearings, bushings, ball bearings, simmerrings, ect.

Universal use for automobile, truck, municipally, country and forestery technology, ect.

Contents:
4 x step discs
4 x pulling spindle and nuts
8 x thrust bolts M10, M12, M14, M16,
20 x pressure sleeves:
Ø 44x34 mm; Ø 46x36 mm; Ø 48x38 mm;
Ø 50x40 mm; Ø 52x42 mm; Ø 54x44 mm; Ø 56x46 mm; Ø 58x48 mm
Ø 60x50 mm; Ø 62x52 mm; Ø 64x54 mm; Ø 66x56 mm; Ø 68x58 mm
Ø 70x60 mm; Ø 72x62 mm; Ø 74x64 mm; Ø 76x66 mm; Ø 78x68 mm;
Ø 80x70 mm; Ø 82x72 mm

Made in China

16 Pcs Bearing extractor set with slidding hammer, 50148

For removal of Pilot Bushes Bearings etc.
Form blind housings.
One Slide hammer assemble 2.5 jaws.
Made of ultra strong Cr-Mo material
For proffesional use.
Specification:
Thread: M10×1.5; M10×1.5 to M8×1.25, M10×1.5 to M6×1.0
Collects size: 6-13mm; 10-17mm; 15.5-22mm; 22-29mm; 28.5-35mm; 35.5-39mm; 38.5-45mm; 42.5-49mm; 48.5-55mm; 52.5-59mm
Contents:
1x Sliding Hammer Assy
1x 2 Claw Puller Assy
3x Screw Adaptors
10 X Collects
1 X Counter Stay Puller

Made in China