INJECTOR TOOLS

Valve spring compressor, 058-6231

• Designed to compress valve springs on overhead valve engines
• Unique, direct action compressor lever gives better visibility of valve spring retainers located in difficult access areas
• Jaw opening of  35 mm to 200 mm and throat clearance of 250 mm.

Made in China

2 pcs Vacuum cup valve grinder, 50104
For hand use, grinding flat head, unslotted valves.
Suitable for small and large vehicles.
Hardwood handles for easy hand lapping of engine valves.
• Synthetic rubber vacuum cups are resistant to oil, grease, gasoline and are replaceable.
• 1-1/8” & 1-3/8” dia. cups.
• 5/8” & 13/16” dia. cups.

Overhead valve spring compressor, 50109

Description: This overhead valve spring compressor is ideal for removing valve springs, spring retainers by compressing the valve spring retainer and exposing the valve keeper, remove keepers, uncompressing the tool then remove spring. It features a reversible jaw / adaptor and automatic cam-action locking to a re-determined setting.
Specifications:
Easy to operate
Cam action level design for secure valve spring locking into the tool
Allow valve springs and valve stem oil seals to be replaced with the cylinder head
Tool spring depth reach grips to retainer are adjustable to fit most large and small spring applications
For use on a wide range of OHV, OHC and CHV engines.
Not suitable for use on engines with deep seated valves

Made in China

Valve spring compressor master set, 50103

Applicable to: OHV & OHC gas or diesel engines of the following vehicles:
Audi (4 and 5 cylinder), BMW, Chevrolet, Chrysler, Ford, GMC, Honda, Hyundai, Infiniti, Lexus, Lincoln, Mazda, Mitsubishi, Nissan, Porsche (924, 928), Saturn, Volkswagen , (4, 5, 6-cylinder) as well as for most other engines with available valve springs for valves...

Diesel injector Puller set Citroen/Peugeot 2.0/2.2HDi 16V

Diesel injektor puller set to remove locked injectors without removing the cylinder head of Citroen and Peugeot 2.0 and 2.2 HDI engines
Engine code:
DW10ATED4(RHM), DW10ATED/L4(RHT), DW10JATED4(RHW), DW12ATED4/L4(4HW)
Included:
Massive bridge matches perfectly on the cylinder head preventing any damage to the engine block.
Screw M17x1.0 mm
Screw M25x1.0 mm
Nut puller
Bearing plate with bearing
Short and long pins
Injector Sockets 25mm, 29mm
Adapter for pullers

Made in China

22 pcs Injector shaft cleaning set, 01110A916

Features:

To clean the injector shafts and seat as well as the injector surface.

4 pcs Diesel injector socket set, 50322

Special socket for removing and installing of diesel injectors.
Set contains:
1 pc 1/2" Dr. x 22mm(6 point ), 110mm long.
1 pc 1/2" Dr. x 22mm(12 point ), 80mm long.
1 pc 1/2" Dr. x 27mm(12 point ), 80mm long.
1 pc 1/2" Dr. x 28mm(12 point ), 78mm long...

Injector puller set for VAG (Audi / Seat / Skoda / VW), 50363

Features: Designed to extraction, installation and service for FSI injectors and most diesel engines installed in VW, Audi, Seat, Skoda.
Material: CR-Mo and S45C steel
Applicable: FSI petrol engine 1.4, 1.6, 1.8, 2.0, 2.7 V6; 3.0 V6; 3.2 V6; 3.6 V6 и 4.2 V8 ...

Fuel injection test set, 50199

The car fuel pressure diagnostic kit is suitable for most vehicles with a fuel injection system with petrol or gas engines (except Bosch, CIS Jetronic, Throttle Body Systems on GM cars).
Not suitable for diesel engines with high pressure injection pump or direct injection engines due to the low pressure range of the manometer.
Fuel pressure testing is an essential part of the fuel injection system troubleshooting process.
Contents:
The set is equipped with various fittings and connection hoses for testing.
15 "length hose is used for direct connection to 1/4" SAE standard fuel pump shredder valve
An 8 "length hose is for the M6 ​​fuel pressure test hole, and there are also adapters M8; M10; M12; M14 for the corresponding test port on fuel rail.
Aluminum tee to support the connection between the fuel pump and the engine for most cars.
Manometer, protected with a rubber shell, with a diameter of the dial 3-1 / 2 ", with a range of 0-10bar (0-140psi) and two-color coded scale for easy reading. The hoses use rubber nylon resin and the built-in nylon can strengthen the hose with increased stress resistance. The pressure relief valve and 16 "fuel drain hose help to safely release the pressure and easily restore the fuel.
Fuel pump pressure check:
The manometer is designed to easily and quickly check the pressure of the fuel injection pump and the fuel flow.
You can compare the pressure value with the manufacturer's recommended reference range to help diagnose the petrol engine system.
Low fuel pressure can be caused by kink/leak/clog on inlet supply side components, a bad fuel pump or regulator, low tank pressure
High fuel pressure may be caused by a bad fuel pressure regulator or kincked outlet return line.

Made in China

27 mm 1/2"Dr. HDI Engines Diesel Fuel Filter socket, 50640

Specially designed for easy disassembly of the fuel filter without damaging the plastic cover. Allows to be tightened to the corresponding torque, preventing air leakage and other malfunctions. It saves time.
Application:
Citroen C4 2.0 HDi 16V, C4 Picasso 2.0 / 2.2 HDi. C5 /, C8 2.0 / 2.2 HDi 16V, Jumpy 2.0 / 2.2 HDi
Fiat: Scudo / Ulysse Mk II 2.0 JTD 16V
Ford Focus / Focus C-Max / Galaxy / Kuga / S-Max 2.0 TDCi
Peugeot: 307/308/407/607/807 / Expert 2.0 HDi 16V
Volvo: C30 / C70 / S40 Mk II / V50 2.0 Diesel (136 HP)...

27 mm 1/2"Dr. HDI Engines Diesel Fuel Filter socket, 9G0123

Specially designed for easy disassembly of the fuel filter without damaging the plastic cover.
Allows to be tightened to the corresponding torque, preventing air leakage and other malfunctions.
It saves time

Diesel Injector extractor set, 50633

For removal of diesel injectors
Various adaptors make the kit suitable for most diesel injectors
Includes also the following components:
M14 x 1.5 for Delphi adaptor
M17 x 1 for Bosch adaptor
M20 x 1 for Denso adaptor
M25 x 1 for Siemens adaptor
M27 x 1 for Siemens adaptor
M27 x 1 for Bosch injector nozzle adaptor

Puller with M14 x 1.5P

3 x different slide hammers:
1.6 kg, 160 mm length
2.7 kg, 460 mm length
5.1 kg, 600 mm length

2 x pulling claws with fork opening:
13.7 x 18 mm, 105 mm length
12.7 x 19 mm, 130 mm length

5 x  Oxygen Sensor slotted 6-pt 1/2" sockets, 100 mm length sizes 25 - 27 - 28 - 29 - 30 mm

Injector extractor, sleeve design, with shells outer diameter 35 mm, internal diameter 29 mm, M17 x 1.0 spindle
Pulling adapter with external thread M27 x 1.0 (3pcs) and M25 x 1.0
Pulling adapter with internal thread M27 x 1.0 (3pcs)
Sliding hammer adapter for inner, outer and claw extractor.

Made in China

Diesel injector copper washer remover install tool, 50629
Size: inner hole 7mm

•     Designed for use on most Common Rail CDI injectors to remove copper washer sealing the base of the injector.
•     Suits most European cars using Bosch CDI fuel injection
•     Handy screw thread and expanding jaw design
•     Remove and install the copper washers on diesel injectors quickly and effectively with this special tool.
•     The reach of 230mm long is designed to install copper washers on deep seated injectors.
•     For removing and installing the copper wires on diesel injector.
•     Quick & effective. Reach - 230mm.

    For deep seated injectors.
    Manufactured from Chrome Vanadium...

BENZ truck diesel injection valve socket, AN040062

The tool remove and install diesel injection valve.

Application: MAN (422, 403) BENZ Truck, SCANIA